While you can tile either of the two first, the popular view based on experience is that it's easier to tile the walls first and then the floor, if you're placing both tiles in a room. This ensures that you keep the tiles clean, since you won't have to work so much around them once installed. The principle of tile installation is that the tile wall “hangs” above the tiled floor. The best way to achieve this result is to first place tiles on the floor so that the wall tile appears to be “sitting” on the bathroom floor.
Before anything else, invest in a professional gutter cleaning service such as Gutter Cleaning Newtown PA to make sure that your gutters won't cause any damage once you install the tile. Clogged gutters can cause moisture to your home interior.
Ideally, you might want to try a mix of both ways. What you really want to do is cover the walls starting with the second row and work your way up from there. The first row, close to the floor, must be reserved with a ledger or other space-saving device. Because the wall tile must hang above the floor tile, it can be more complicated to install the tile on the wall first.
However, starting your project first with installing tiles on walls can help you avoid messes and unfortunate damage related to mishap with mortar and tile. To answer your question, yes, I always put tiles first on the shower walls and, finally, the floor. I do this for two main reasons. Watch my video on how to tile the floor and curb of a shower.
The main reason to install the wall tile first is for easier installation. When installing wall tiles, you don't have to wait for the tile to harden or worry about damaging the tile. Therefore, it not only allows for a simpler installation process, but it is also faster. Draw a diagram of your bathroom floor and measure the “exposed” area of the floor.
If you have a bathtub installed with a side panel, you may not need to place tiles under the tub, but if you have a bathtub with a separate roll-top, you may need to remove it before tiling the entire floor. Once you have the bathroom plan, it's time to calculate the floor area in square meters by multiplying the dimensions of the sides of the rectangle in meters (if you measure your room in centimeters, the floor area in cm2 can be converted to m2 by dividing it by 10,000). Some tiles will probably have to be cut the same way: few rooms can be equipped perfectly. In addition, walls and floors are rarely square with parallel sides, so it will be necessary to make some cuts to adjust them.
This means that the calculated area of the wall or tile floor and the usable number of tiles are unlikely to match. You'll have to overestimate to account for this discrepancy. The usual amount quoted can be as low as 5% and as high as 20%. It's easier to allow a small percentage in very large areas, while small areas are likely to generate more waste.
A typical allowance would be 5 to 10% for an experienced tiler or DIY expert and 10 to 20% if this is the first time doing so. Since it's always worth having replacement tiles (just in case), it's much safer to overestimate them than to have to buy more tiles, the bathroom walls must be tiled before tackling the floor to avoid damaging the floor. This isn't always practical if the floor needs to be in place, ready to fit the bathroom units and the suite. If you need to tile the floor before starting the bathroom walls, make sure that the tiles are well protected with a hard layer rather than just a cloth.
There's rarely a problem if you can't complete the bathroom tiling in one day, but if you have to remove the tiles or find that the tiles aren't aligned when you've walked through the bathroom, it can be expensive and wasteful to have to correct a tiling problem that would otherwise be avoided. Max is from Pittsburgh, but was helping his son and daughter-in-law remodel their bathroom in Virginia. Don't assume that the walls are square; it's best to draw a horizontal reference line at the final height around the bathroom or choose the level that best suits the bathroom window, bathtub countertop, or other key feature. If you are tiling the bathroom floor, it's worth removing and storing the bathroom door until the tiles are in place, in case the new floor height interferes with opening and closing the door.
In a small bathroom, you can simply place the tiles to get a symmetrical center line; otherwise, measure and mark a center along the length, divide this line, and mark a second center line across the width on the bathroom floor. A wealth of construction experience allows James to provide practical advice for those considering remodeling a bathroom. Many professional bathroom remodelers use Wedi for customers because it has a great warranty, is quick to install and is 100% waterproof. .
.
Leave a Comment